The URL can be used to link to this page

Home My WebLink AboutBLDG PERMIT #8809 (Fire Alarms/Smoke detectors)CITY OF CAPE CANAVERAL DOCUMENT COVER SHEET BOX #: 1 Item #40 — 230 Columbia Dr.; Permit #8809; Fire Alarms/Smoke Detectors 2 pages UPON RETURN OF PAPER ORIGINALS FROM MCCI, add to file name: NOTES: 1. ELECTRICAL CONTRACTORS TO PROVIDE CONNECTIONS TO THE POWER SERVICE BY MEAN OF A DEDICATED BRANCH CIRCUIT. THE CIRCUIT DISCONNECTING MEANS SHALL HAVE A RED MARKING AND BE IDENTIFIED AS "FIRE ALARM CIRCUIT CONTROL' THE LOCATION OF THE CIRCUIT DISCONNECTING MEANS SHALL BE PERMANENTLY IDENTIFIED AT THE FIRE ALARM CONTROL UNIT. 2. FIRE ALARM CONTRACTOR TO TIE DUCT -SMOKE DETECTORS IF ANY, INTO FIRE ALARM SYSTEM AND PROVIDE FOR SYSTEM SHUTDOWN. 3, FIRE ALARM PANELS WILL NOT CONTAIN ANY WIRE NUTS, OR SIMILAR CONNECTIONS, WITHIN THE PANEL, EXCEPT FOR THE CONNECTION TO THE PRIMARY POWER SUPPLY. 4. ANY PENETRATIONS MADE THROUGH A FIRE RATED ASSEMBLY SHALL BE PROPERLY SEALED TO MAINTAIN THE INTEGRITY OF THE ASSEMBLY PER U.L. AND NFPA 5. DEVICES ARE NOT DRAWN TO SCALE; POSITIONS MAY VARY DUE TO PHYSICAL AND/OR DECOR LIMITS. 6. WIRE RUNS ARE ILLUSTRATED TO SHOW THE DEVICE SEQUENCE AND CIRCUIT CONTINUITY ONLY. 7. WALL MOUNTED SPEAKERIHORN STROBES & STROBES SHALL BE PLACED 80" AFF. CEILING MOUNTED TO THE BOTTOM OF CEILING STRUCTURAL STEEL AT LESS THAN 30' AFF. DEVICES MUST BE ABOVE AND CLEAR OF ANYIALL MATERIAL 8. FOR MANUAL PULL STATIONS MAXIMUM FORWARD REACH SHALL BE NO MORE THAN 48'. 9. A ZONE MAP SHALL BE POSTED AT THE FIRE ALARM PANEL AND REMOTE ANNUNCIATORS. 10. PROVIDE "BACK BOXES ON ALL APPLIANCES OR DEVICES PER NFPA # 70 OR PER MANUFACTURERS INSTRUCTIONS. 11. DO NOT INSTALL SMOKE DETECTORS IN THE DIRECT PATH OF AIR FLOW FROM SUPPLY. INSTALL AT LEAST 3 FEET FROM AIR VENTS, NO EXCEPTIONS PER NFPA 72. 12. NO DEVIATION OF HORIZONTAL SPACING AS SHOWN ON DRAWINGS BETWEEN STROBES & HORN/STROBES & MINI-HORN/STROBES. FOR COMPLIANCE WITH NFPA CODES AND STANDARDS & A.D.A. 13. ALL CONDUIT SHALL BE 314' MINIMUM. 14. INSTALLATION PERSONNEL SHALL BE SUPERVISED BY PERSONS WHO ARE QUALIFIED AND EXPERIENCED IN THE INSTALLATION, INSPECTION, AND TESTING OF FIRE ALARM SYSTEMS. EXAMPLES OF QUALIFIED PERSONNEL SHALL INCLUDE, BUT NOT BE LIMITED TO THE FOLLOWING: a. FACTORY TRAINED AND CERTIFIED PERSONNEL b. NATIONAL INSTITUTE OF CERTIFICATION IN ENGINEERING TECHNOLOGIES (NICET) FIRE ALARM LEVEL II CERTIFIED PERSONNEL c. PERSONNEL LICENSED OR CERTIFIED BY STATE OR LOCAL AUTHORITY. 15. THE LOCATION OF ALL DUCT SMOKE DETECTORS SHALL BE PERMANENTLY AND CLEARLY IDENTIFIED AND RECORDED. THIS IS USUALLY ACCOMPLISHED BY PROVIDING A SEPARATE ZONE FOR EACH DETECTOR OR BY PROVIDING REMOTE INDICATORS SO THAT THEY WILL BE VISIBLE FROM THE FLOOR LEVEL. IN ADDITION, A PLACARD SHALL BE PLACED OUTSIDE THE FIRST POINT OF ACCESS TO REACH THE DETECTOR. FOR EXAMPLE, THE PLACARD MAY BE MOUNTED ON THE WALL BENEATH THE CEILING TILE THAT MUST BE REMOVED TO ACCESS THE DUCT. 16. A STICKER SHALL BE CONSPICUOUSLY AFFIXED TO THE SIGNALING SYSTEM COMPONENT IDENTIFYING THE CENTRAL STATION BY NAME AND TELEPHONE NUMBER. UFSRS 69A-48.008 17. HORNISTROBES SHALL BE SYNCHRONIZED. 18. THE MONITORING FACILITY SHALL BE A U.L. LIST REMOTE STATION. PROVIDE THE NAME OF THE PROPOSED COMPANY FOR APPROVAL SFM 69A48. 19, SCOPE OF WORK 15 INSTALLING AN ADDITIONAL FIRE ,ALARM SYSTEM . FIRE ALARM SYMBOL LEGEND FIRE ALARM CONTROL PANEL FSA FIRE SYSTEM ANNUNCIATOR Website: www.adssecurity.com POWER EXPANSION PANEL ORIGINAL'S DATE: VOICE EVACUATION C/0 CARBON MONOXIDE DETECTOR N/A WP HEAT & HEAT DETECTOR P SMOKE DETECTOR N/A MANUAL PULL STATION DATE: WP STROBE/STROBE 8 WP,CEILING & WALL SPEAKER/STROBE MINI HORN SPEAKER ONLY e HORN/STROBE, CEILING H/S Nina H. Percival 86 WEATHER PROOF H/S SELL BELL ti DUCT -SMOKE DETECTOR INTI DUCT -SMOKE REMOTE INDICATOR ADS473 RELAY OR IN PANEL RELAY AS—BUILT: SPRINKLER WATER FLOW SWITCH JOB NUMBER: 5783118001253 SPRINKLER VALVE TAMPER SWITCH I SHEET 1 OF 2 END OF LINE RESISTOR WARNING LIGHT ELEVATOR SUPPRESSION SYSTEM E C�i ELECTRICAL CONTACTOR 30v "W R 30V SURGE PROTECTION 12UV SURGE PROTECTOR 120V SURGE PROTECTION Rn� PHONE LINE SURGE PROTECTION KNOXBOX �H DOOR HOLDER C INPUT MODULE WIRE RISER JUNCTION BOX saa' SCI EOL DEVICE �A VOICE SYSTEM ANNUNCIATOR City of Cape Canaveral PERMITTED € OR CO S RIC N RE\11,1 t', TD Review, o� 1eti pl � a..— o pot aut, n viol o� ��{Illttt// sm local, owe . a, Ed Bradeso din noes or stat, 's ,%��, C LAie'�/�I� s• (yj;.• �C E /yS% ,�� F • ;� +moi *•; No 58238 •: ® STATE OF : Oj L.P. Fortune Place, Suite A, West Melbourne, Florida 32904 ADS4356 Sales: (321) 254-8877 4 11 Fac: (321) 25382265 Website: www.adssecurity.com ARCHITECTS JOB A ORIGINAL'S DATE: ARCHITECTURAL REFERENCE it LAST REVISION: ARCHITECT: N/A N/A N/A N/A N/A ALARM SYSTEM DESIGN BY- DATE: Ira Thompson 05-17-12 Fire Alarm Contractor:N: IV: 04 NICET Fire AlarmLevel 10272743 3 COLONIAL HOUSE CONDOMINIUM DRAWN BY: DATE - Nina H. Percival 05-25-12 230 COLUMBIA DRIVE CAPE CANAVERAL, FL 32920 .Ya CHECKED BY: DATE: SCALE: CADD CODE: 1/16" =1' ADS473 AS—BUILT: DATE: JOB NUMBER: 5783118001253 FIRE ALARM SYSTEM SHOP DRAWINGS DRAWN WITH AUTOCAD 1 I SHEET 1 OF 2 NOTES: 1. ELECTRICAL CONTRACTORS TO PROVIDE CONNECTIONS TO THE POWER SERVICE BY MEAN OF A DEDICATED BRANCH CIRCUIT. THE CIRCUIT DISCONNECTING MEANS SHALL HAVE A RED MARKING AND BE IDENTIFIED AS "FIRE ALARM CIRCUIT CONTROL' THE LOCATION OF THE CIRCUIT DISCONNECTING MEANS SHALL BE PERMANENTLY IDENTIFIED AT THE FIRE ALARM CONTROL UNIT. 2. FIRE ALARM CONTRACTOR TO TIE DUCT -SMOKE DETECTORS IF ANY, INTO FIRE ALARM SYSTEM AND PROVIDE FOR SYSTEM SHUTDOWN. 3. FIRE ALARM PANELS WILL NOT CONTAIN ANY WIRE NUTS, OR SIMILAR CONNECTIONS, WITHIN THE PANEL, EXCEPT FOR THE CONNECTION TO THE PRIMARY POWER SUPPLY. 4. ANY PENETRATIONS MADE THROUGH A FIRE RATED ASSEMBLY SHALL BE PROPERLY SEALED TO MAINTAIN THE INTEGRITY OF THE ASSEMBLY PER U.L. AND NFPA 5. DEVICES ARE NOT DRAWN TO SCALE; POSITIONS MAY VARY DUE TO PHYSICAL ANDIOR DECOR LIMITS. 6. WIRE RUNS ARE ILLUSTRATED TO SHOW THE DEVICE SEQUENCE AND CIRCUIT CONTINUITY ONLY. 7. WALL MOUNTED SPEAKERIHORN STROBES & STROBES SHALL BE PLACED 80' AFF. CEILING MOUNTED TO THE BOTTOM OF CEILING STRUCTURAL STEEL AT LESS THAN 30' AFF. DEVICES MUST BE ABOVE AND CLEAR OF ANY/ALL MATERIAL 8. FOR MANUAL PULL STATIONS MAXIMUM FORWARD REACH SHALL BE NO MORE THAN 48'. 9. A ZONE MAP SHALL BE POSTED AT THE FIRE ALARM PANEL AND REMOTE ANNUNCIATORS. 10, PROVIDE'BACK BOXES ON ALL APPLIANCES OR DEVICES PER NFPA # 70 OR PER MANUFACTURERS INSTRUCTIONS. 11. DO NOT INSTALL SMOKE DETECTORS IN THE DIRECT PATH OF AIR FLOW FROM SUPPLY. INSTALL AT LEAST 3 FEET FROM AIR VENTS, NO EXCEPTIONS PER NFPA 72. 12. NO DEVIATION OF HORIZONTAL SPACING AS SHOWN ON DRAWINGS BETWEEN STROBES & HORN/STROBES & MINI-HORNISTROBES. FOR COMPLIANCE WITH NFPA CODES AND STANDARDS & A.D.A. 13. ALL CONDUIT SHALL BE 3/4' MINIMUM. 14. INSTALLATION PERSONNEL SHALL BE SUPERVISED BY PERSONS WHO ARE QUALIFIED AND EXPERIENCED IN THE INSTALLATION, INSPECTION, AND TESTING OF FIRE ALARM SYSTEMS. EXAMPLES OF QUALIFIED PERSONNEL SHALL INCLUDE, BUT NOT BE LIMITED TO THE FOLLOWING: a. FACTORY TRAINED AND CERTIFIED PERSONNEL b. NATIONAL INSTITUTE OF CERTIFICATION IN ENGINEERING TECHNOLOGIES (NICET) FIRE ALARM LEVEL II CERTIFIED PERSONNEL c. PERSONNEL LICENSED OR CERTIFIED BY STATE OR LOCAL AUTHORITY. 15, THE LOCATION OF ALL DUCT SMOKE DETECTORS SHALL BE PERMANENTLY AND CLEARLY IDENTIFIED AND RECORDED. THIS IS USUALLY ACCOMPLISHED BY PROVIDING A SEPARATE ZONE FOR EACH DETECTOR OR BY PROVIDING REMOTE INDICATORS SO THAT THEY WILL BE VISIBLE FROM THE FLOOR LEVEL. IN ADDITION, A PLACARD SHALL BE PLACED OUTSIDE THE FIRST POINT OF ACCESS TO REACH THE DETECTOR. FOR EXAMPLE, THE PLACARD MAY BE MOUNTED ON THE WALL BENEATH THE CEILING TILE THAT MUST BE REMOVED TO ACCESS THE DUCT, 16. A STICKER SHALL BE CONSPICUOUSLY AFFIXED TO THE SIGNALING SYSTEM COMPONENT IDENTIFYING THE CENTRAL STATION BY NAME AND TELEPHONE NUMBER. UFSRS 69A-48.008 17. HORNISTROBES SHALL BE SYNCHRONIZED. 18. THE MONITORING FACILITY SHALL BE A U.L. LIST REMOTE STATION. PROVIDE THE NAME OF THE PROPOSED COMPANY FOR APPROVAL SFM 69AA8. 19. SCOPE OF WORK IS INSTALLING AN ADDITIONAL FIRE ALARM SYSTEM. FIRE ALARM SYMBOL LEGEND P FIRE ALARM CONTROL PANEL �A FIRE SYSTEM ANNUNCIATOR FE POWER EXPANSION PANEL VEVAC VOICE EVACUATION CIO CARBON MONOXIDE DETECTOR COLOR WP HEAT & HEAT DETECTOR P SMOKE DETECTOR ®✓ MANUAL PULL STATION SURFACE & LOCATION WP STROBE/STROBE TYPE WP,CEILING & WALL SPEAKER/STROBE MINI HORN FSA SPEAKER ONLY PUO HORN/STROBE, CEILING H/S EMT & WEATHER PROOF H/S BLLL BELL ti DUCT -SMOKE DETECTOR STI DUCT -SMOKE REMOTE INDICATOR 18 RELAY OR IN PANEL RELAY 2 SPRINKLER WATER FLOW SWITCH n SPRINKLER VALVE TAMPER SWITCH -•t'�l�i'® END OF RESISTOR RED/BLACK B ELEVATOR WARNING LIGHT 12 SOLID 2 SUPPRESSION SYSTEM YES ELECTRICAL CONTACTOR 3W suRR 30V SURGE PROTECTION � 12DV SUR I YaG CTOR 120V SURGE PROTECTION P D� PHONE LINE SURGE PROTECTION TO NFPA 72 (2002) KNOXBOX DHI DOOR HOLDER M INPUT MODULE WIRE RISER C JUNCTION BOX a )snca EOL DEVICE VS,A VOICE SYSTEM ANNUNCIATOR SLC LOOP R-07 R-06 R-05 S-04 S-03 S-02 S-01 EX/STING FRCP WIRE & CABLE SCHEDULE ASSIGN. WIRE GAUGE SOLID/ NUMBER OF MOUNTING WET PLENUM CONNECTOR USE COLOR (mounting) TYPE STRANDED CONDUCTORS SURFACE & LOCATION RATED TYPE DEVICES FSA BOSCH D7033 FULL EMT RATED NIA 1 A FPLP 18 SOLID 2 YES YES NO TERMINAL INITIATING CIRCUIT RED/BLACK B FPLP 12 SOLID 2 YES YES NO TERMINAL INDICATING CIRCUIT RED/BLACK SMOKE BOSCH D7050 TO NFPA 72 (2002) CEILING or NIA N/A 4 DETECTOR WHT/GRN C FPLP 18 SOLID 4 YES YES NO TERMINAL DUCT SMOKE DETECTOR, RED/BLACK I N/A 4 4" OCT FSA WHT/GRN COLONIAL HOUSE CONDOMINIUM Fire Alarm System Riser 94700 0000 EMSTING SILENT KNIGHT 505 il4t 9N7C Mt M VCO 120VAC DEDICATED CIRCUIT (INSTALLED BY OTHERS) 064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 MH -2.1.1 MH -2.1.2 MH -2.1.3 MH -2.1.4 MH -2.1.5 MH -2.1.6 MH -2.1.7 MH -2.1.8 MH -2.1.9 MH -2.1.10 MH -2.1.11 MH -2.1.12 MH -2.1.13 MH•2.1.14 MH -2.1.15 M11-2.1.16 MH -2.1.17 MH -2.1.18 MH -2.1.19 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 MH -2.2.1 MH -2.2.2 MH -2.2.3 MH -2.2.4 MH -2.2.5 MH -2.2.6 MH -2.2.7 MH -2.2.8 MH -2.2.9 MH -2.2.10 MH -2.2.11 MH -2.2.12 MH -2.2.13 MH -2.2.14 MH -2.2.15 MH -2.2.16 MH -2,2.17 MH -2.2.18 MH -2.2.19 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 .064 MH -2.3.1 MH -2.3.2 MH -2.3.3 MH -2.3.4 MH -2.3.5 MH -2.3.6 MH -2.3.7 MH -2.3.8 MH -2.3.9 MH -2.3.10 MH -2.3.11 MH -2.3.12 MH -2.3.13 MH -2.3.14 MH -2.3.15 MH -2.3.16 MH -2.3.17 MH -2.3.18 MH -2.3.19 FIRE ALARM DEVICE SCHEDULE APPLIANCE/ MANUFA- MODEL COVERAGE HEIGHT dBA CANDELLA NUMBER DEVICE CTURER NUMBER (MAXIMUM) (mounting) OF TYPE DEVICES FSA BOSCH D7033 FULL S 60" NIA NIA 1 SYSTEM POWER SILENT SK5495 FULL <_ 72" NIA N/A 1 EXPANDER KNIGHT SYSTEM SMOKE BOSCH D7050 TO NFPA 72 (2002) CEILING or NIA N/A 4 DETECTOR CHAPER 5 4" OCT WALL BASE BOSCH D7050 -B6 N/A CEILING NIA N/A 4 4" OCT EXPANSION BOSCH D7039 N/A N/A N/A NIA 1 MODULE OUTPUT BOSCH D7053 N/A N/A NIA NIA 3 MODULE MINI HORN WHEELOCK WH-HNR 30'X 30' 80" AFF 99 N/A 54 MINI HORN WHEELOCK WH-ESBR 30'X 30' 80" AFF NIA N/A 54 BACK BOX 120V SURGE DITEK DTK120/240 PRIMARY T FROM N/A N/A 1 PROTECTION POWER PANEL --------------- RECHARGEABLE PATROL ASLA-1075 BACKUP IN PANEL NIA NIA 2 BATTERY POWER 7AH/12VDC POWER SIGNAL CIRCUIT # 2.1 (CLASS B, STYLE Y) LINE LOSS CALCULATION 1.98 X 0.681'X 2 = 2.620 OHMS X 1.024A = 2.692 VOLTAGE DROP SIGNAL CIRCUIT # 2.2 (CLASS B, STYLE Y) LINE LOSS CALCULATION 1.98 X.669'X 2 = 2.582 OHMS X 1.216A = 3.140 VOLTAGE DROP SIGNAL CIRCUIT # 2.3 (CLASS B, STYLE Y) LINE LOSS CALCULATION 1.98 X.679'X 2 = 2.620 OHMS X 1.216A = 3.187 VOLTAGE DROP